The uP4-Din is a DIN rail mount, universal single input indicator, which gives easy interface with a wide range of sensors. It is also fitted with two relay outputs (with two setpoint indicator LEDs), and one optional retransmission analogue output (4~20mA or 0~10Vdc selectable).
The uP4-Din has a 4-digit LED front display, and a universal power supply of 24~250Vac / 19.5~250Vdc.
Setup and calibration is simple, using ‘uP Configure’ software (version 1.5.23 or later), with step-by-step instructions.

Features:

• Universal Input with Indication.
• DIN Rail Mount.
• Universal AC or DC supply 24~250Vac / 19.5~250Vdc.
• Two Relay Outputs (with Setpoint LEDs).
• Option to add One Retrans Analogue Output (4~20mA or 0~10Vdc selectable).
• Programmable via USB Port using uP Configure Programming Software (version 1.5.23 or later) and the XU-USB (Rev 1) key.
• Simple setup and calibration.
• 4-digit LED display with Transparent Cover.
• Sensor power supply for powering external transmitter.
• Low cost.

Universal Power Supply of 24~250Vac / 19.5~250Vdc.

Note: The uP4-Din Universal Input Indicator is pre-programmed for RTD Pt100 input as standard.

To program the uP4-Din requires the XU-USB (Rev 1) Programming Key:

USB Programming Key for programming uP4-Din using uP Configure Programming Software (version 1.5.23 or later).
Note: XU-USB must be (Rev 1) or later! Older versions will NOT connect with the uP4-Din.

(Same Key as used for programming XU Series transmitters, 2400-A16 / 2400-M-R, Z-2400-Sleeper, Z-2400-A2 Series
and IN-uP4.)

 

 

Input Specifications
Excitation:	Sensor Power Supply	+22Vdc ±10%, 25mA max.
Voltage DC Input:	mV Range	-200mV~200mV.
	V Range	0~1V, 0~10V, -10~30V, 0~300Vdc.
	Linearity and Repeatability	<±0.02% FSO typical.
Current Input:	mA Range	0~20mA (4~20mA).
	Input Resistance	10Ω.
	Linearity and Repeatability	<±0.02% FSO typical.
Thermocouple Input:	Thermocouple Types	B, E, J, K, N, R, S, T.
	Input Impedance	1MΩ Minimum
	T/C Lead Resistance	100Ω Maximum
	Cold Junction Compensation	-10~70°C
	Accuracy	E, J, K, N, T <±1°C/ C. B, R, S <±2°C.
RTD Input:	RTD Input	Pt100 or Pt1000 DIN 3-wire Type. (2-wire can be used with offset calibration.)
	Lead Wire Resistance	Pt100: 50Ω/wire Maximum. 0.02% FSO Offset Error per Ω of Lead Resistance. Pt1000: 20Ω/wire Maximum. 0.002% FSO Offset Error per Ω of Lead Resistance.
	Accuracy	Better than 0.2°C.
	Linearity (Pt100)	0.02% FSO for Span Inputs ≤200°C. 0.1% FSO for Span Inputs ≤300°C.
	Linearity (Pt1000)	0.02% FSO for Span Inputs ≤200°C. 0.2% FSO for Span Inputs ≤300°C.
NTC Thermistor Input:	NTC Sensor Types	10K (Beta 3984) -55~125°C, 10K (Beta 3435) -50~120°C.
Pulse & Frequency Input:	Input Type	Open Collector – NPN, PNP.
	Frequency Range	0~2000Hz.
	Software Modes	General Frequency, Flow Rate or RPM.
Potentiometer Input:	Potentiometer input	3-wire.
	Excitation voltage	Variable.
	Potentiometer resistance	<1kΩ low pot; 1~4kΩ med pot; 4~20kΩ high pot. Output type software selectable.
Output Specifications
Analogue Output:	mA Range	0~20mA (4~20mA) Active.
	V Range	0~10Vdc Active.
	Isolation	1400Vrms for 1 minute. Working voltage 125V.
	Output Drive	20mA, 600Ω at 12Vdc.
	Accuracy / Repeatability	0.05% of FSO.
Relay Outputs:		2 Isolated Relays with LED indication on each output.
	Functions	2 on Board Controllers can be used as Set Point (SV), Switching Differential, Auto/Manual, Manual Output Setting, Dual Action Control, Single Action Control, Heat/Cool, Cool Only, Heat Only.
	Relay Type & ratings	Relay 1: Form A, 3A max 120/240Vac or 28Vdc (resistive load). Relay 2: Form C, 10A max 120/240Vac or 28Vdc (resistive load). 24~250Vac / 19.5~250Vdc (47-63Hz, 6VA max).
Power Supply Specifications
	Isolation	2300Vrms for 1 minute to all inputs and outputs.
Case Specifications
	IP Rating	IP20.
	DIN Rail Mount	35mm
	Display	4 digits with Plastic Protective Flap.
	Dimensions	H=112mm, W=23mm, D=120mm.