Monnit Industrial Pressure Wireless Sensor
 
Search
Menu Close

Monnit Industrial Pressure Wireless Sensor

Monnit’s Industrial Wireless Pressure Meter monitors gas, liquid, or vapor supply lines
Part Number: MNS2-4-IN-PS-xxx
Manufacturer:
0Types Available
Back to Previous Page

Always know supply line pressure

Monnit’s Industrial Wireless Pressure Meter monitors gas, liquid, or vapor supply lines. If the pressure within a line, machine, pump, or specialized area (e.g., negative pressure tent or cleanroom) falls out of a user-defined range, an alert will be sent in real time via text, email, or call.

Available in 50 and 300 pounds per square inch gauge (PSIG) meters, these sensors use a five-volt pressure transducer to measure the pressure within a supply line. Collected data is transmitted to iMonnit Sensor Configuration and Management Software for analysis and action.

By connecting the sensor to a pressurised gas, liquid, or vapor supply line, you can measure the pressure within the line and review the data in the iMonnit Online Sensor Monitoring and Notification System. The data is stored in the online system and can be reviewed within the system on dashboards and charts or exported as a data sheet or graph. You can customise settings to your use case and set notifications and alerts in the cloud-based software to know immediately via text, email, or call if the pressure is above or below an optimal range.


A lab - and machine - ready sensor

This sensor comes with an industrial battery included with the life of up to 7 years

All industrial sensors are enclosed in a reliable, weatherproof NEMA-rated enclosure that are constructed for both indoor and outdoor use. These rugged enclosures protect the sensor circuitry against;

  • Falling dirt
  • Wind-blown dust
  • Rain, sleet, snow, splashing water, and hose-directed water
  • Ice formation on the enclosure
  • Increased resistance to corrosion


Features

  • Impressive wireless range of up to 1,200 feet through walls
  • Frequency-hopping spread spectrum (FHSS)
  • Improved interference immunity
  • Improved power management for longer battery life
  • Encrypt-RF® Security (Diffie-Hellman Key Exchange + AES-128 CBC for sensor data messages)
  • Stores 2000 to 4000 readings if gateway connection is lost (non-volatile flash, persists through the power cycle)
    • 10-minute heartbeats = ~ 22 days
    • 2-hour heartbeats = ~ 266 days
  • Over-the-air updates
  • Free iMonnit basic online wireless sensor monitoring and notification system to configure sensors, view data and set alerts via SMS text and email


Applications

  • Compressed air supply lines
  • Water supply lines
  • Gas supply lines
  • Pumping systems
  • Irrigation system pressure
  • Industrial process monitoring
  • Trash compaction equipment
  • HVAC/R
  • Chemical Processing


IMPORTANT - Sensor Operation

Please note: this sensor requires both an applicable Gateway and iMonnit software to operate. For further information, please refer to the tabs above or related products below.


Monnit Gateway Options

An integral component of any IoT network is the gateway. A gateway device allows for data from sensors to be transmitted to the iMonnit software platform.


Monnit Ethernet Wireless Gateway 4

Monnit’s Ethernet Gateways allow your Monnit Wireless Sensors to communicate with the iMonnit™ Online Wireless Sensor Monitoring and Notification System without the need for a PC. Simply provide power and plug the gateway into an open Ethernet network port with an internet connection. It will then automatically connect with our online servers, providing the perfect solution for commercial locations where there is an active internet connection.

Learn more about the Ethernet Wireless Gateway 4>>



Monnit 4G + Ethernet IoT Gateway

The ALTA® by Monnit Wireless IoT Gateway combines a 4G LTE CAT-M1/NB2 cellular engine and Ethernet platform with Monnit’s wireless access point network to aggregate and communicate data from Monnit ALTA Wireless Sensors. The ALTA IoT Gateway allows ALTA Sensors to operate on the world’s leading cellular networks and stay connected to the Internet. The gateway uses AC main power but also has redundant power through a battery backup lasting up to 60 hours.

To meet the global demand for enterprise IoT deployment, the IoT Gateway communicates with the cloud-based iMonnit® monitoring software via cellular transmission, making it ideal for remote locations or where the Internet isn’t available. The RJ-45 Ethernet jack allows local device configuration, diagnostics, and connectivity backup. The IoT Gateway is instrumental in sending sensor notifications via text, email, or call if user-defined conditions are met or exceeded.

Learn more about the 4G + Ethernet Wireless Gateway 4>>


Online Sensor Monitoring Software

iMonnit is a cloud based mobile internet platform and central hub for managing Monnit and ALTA products. All data is secured on dedicated servers operating Microsoft SQL Server. This online user interface is where all your device settings can be arranged, supervised, and modified to reflect your unique environment. OneTemp will look after the activation and setup of your new online iMonnit account free of charge. There is also a free mobile app for you to stay in control at all times. Start with the basic version or upgrade to iMonnit Premiere to enjoy the full features your Monnit experience can offer.


iMonnit Basic Vs Premiere:

  • Basic - Free with no ongoing costs
    Monnit Basic is included for free with all wireless sensors, providing basic features for you to configure and monitor your sensors online. These basic features only support one network and one registered user on an account.
  • Premiere - Minimal Annual Fee
    iMonnit Premiere allows for enhanced functionality of your wireless sensors and includes an advanced software feature set at a low annual cost. All of iMonnit's advanced features are availble for configuration. You can have more sensors on your account, support multiple users, and view floorplans for all your sensors.

Learn more about the iMonnit Premier Online Software>>

 


Technical Information

Pressure Meter Specifications

Supply voltage 2.0-3.8 VDC
Current consumption 0.2 μA (sleep mode), 0.7 μA (RTC sleep), 570 μA (MCU idle),
2.5 mA (MCU active), 5.5 mA (radio RX mode), 22.6 mA (radio
TX mode)
Operating temperature range (board circuitry and battery) -40°C to +85°C (-40°F to +185°F)
Included battery Max temperature range -40° to +85°C (-40° to +185°F)
Capacity 1500 mAh Lithium Thionyl Chloride
Data logging Data logs 2000 to 4000 readings if the gateway connection is
lost (non-volatile flash, persists through the power cycle):
10-minute Heartbeats = ~ 22 days; 2-hour Heartbeats = ~ 266
Wireless protocol ALTA Proprietary Frequency-Hopping Spread Spectrum (FHSS)
Wireless transmission power 50 mW (900MHz), 25 mW (868 MHz), 10 mW (433 MHz)
Wireless antenna type 1/2-wave waterproof dipole with RP-SMA connector and swivel
neck; dBi of 3.0 (900/868MHz) or 2.5 (433 MHz); length of 8.27"
(210mm) (900/868MHz) or 7.68" (195mm) (433 MHz); diameter
at thickest point of 0.55" (14mm)
Wireless range 1,200+ ft non-line-of-sight
Resolution 0.1 PSI
Security Encrypt-RF® (256-bit key exchange and AES-128 CTR)
Weight 13.3 ounces
Enclosure rating NEMA 1, 2, 4, 4x, 12, and 13 rated, sealed, and weatherproof
UL rating UL Listed to UL508-4x specifications (File E194432)
Certifications 900 MHz sensors: FCC ID: ZTL-G2SC1 and IC: 9794A-G2SC1.
868 and 433 MHz sensors tested and comply with: EN 55032:
2015/A11:2020; EN 55035:2017/A11:2020; ETSI EN 300 220
V3.2.1 (2018-06); ETSI EN 301 489-3 V2.2.0. (2021-11); and
ETSI EN 303 645. All sensors tested and comply with: EN
61010-1 and EN 60950 and meet RoHS 2015/863 and REAC

Pressure Transducer Specifications

Operating temperature o to 175° F ( -18 to 79°C)
Thermal effect on reading ±0.02% FS/° F. (includes zero and span)
Media Gas, Liquid, or Vapor
Response time 300 msec
Stability 1.0% FS/year (Typ .)
Wire length 3 Feet ( 1 M)
Accuracy 1.0% FS; 0.5% RSS;
(Includes linearity, hysteresis, and repeatability)
Process connection ¼" NPT -Male Standard
Pressure transducer(s) 0- 50 or 0-300

Combined Specifications

Pressure measurement accuracy ± (2% of reading + 1.05% FS)
User -calibrated pressure accuracy ± (0.5% of reading + 0.5% FS) 1

1 For best results, first zero the sensor, then calibrate at greater than 20% of pressure range of the transducer.

Always know supply line pressure

Monnit’s Industrial Wireless Pressure Meter monitors gas, liquid, or vapor supply lines. If the pressure within a line, machine, pump, or specialized area (e.g., negative pressure tent or cleanroom) falls out of a user-defined range, an alert will be sent in real time via text, email, or call.

Available in 50 and 300 pounds per square inch gauge (PSIG) meters, these sensors use a five-volt pressure transducer to measure the pressure within a supply line. Collected data is transmitted to iMonnit Sensor Configuration and Management Software for analysis and action.

By connecting the sensor to a pressurised gas, liquid, or vapor supply line, you can measure the pressure within the line and review the data in the iMonnit Online Sensor Monitoring and Notification System. The data is stored in the online system and can be reviewed within the system on dashboards and charts or exported as a data sheet or graph. You can customise settings to your use case and set notifications and alerts in the cloud-based software to know immediately via text, email, or call if the pressure is above or below an optimal range.


A lab - and machine - ready sensor

This sensor comes with an industrial battery included with the life of up to 7 years

All industrial sensors are enclosed in a reliable, weatherproof NEMA-rated enclosure that are constructed for both indoor and outdoor use. These rugged enclosures protect the sensor circuitry against;

  • Falling dirt
  • Wind-blown dust
  • Rain, sleet, snow, splashing water, and hose-directed water
  • Ice formation on the enclosure
  • Increased resistance to corrosion


Features

  • Impressive wireless range of up to 1,200 feet through walls
  • Frequency-hopping spread spectrum (FHSS)
  • Improved interference immunity
  • Improved power management for longer battery life
  • Encrypt-RF® Security (Diffie-Hellman Key Exchange + AES-128 CBC for sensor data messages)
  • Stores 2000 to 4000 readings if gateway connection is lost (non-volatile flash, persists through the power cycle)
    • 10-minute heartbeats = ~ 22 days
    • 2-hour heartbeats = ~ 266 days
  • Over-the-air updates
  • Free iMonnit basic online wireless sensor monitoring and notification system to configure sensors, view data and set alerts via SMS text and email


Applications

  • Compressed air supply lines
  • Water supply lines
  • Gas supply lines
  • Pumping systems
  • Irrigation system pressure
  • Industrial process monitoring
  • Trash compaction equipment
  • HVAC/R
  • Chemical Processing


IMPORTANT - Sensor Operation

Please note: this sensor requires both an applicable Gateway and iMonnit software to operate. For further information, please refer to the tabs above or related products below.


Picture of Monnit Industrial Pressure Wireless Sensor (50 PSIG)
Monnit Industrial Pressure Wireless Sensor (50 PSIG)
Monnit’s Industrial Wireless Pressure Meter monitors gas, liquid, or vapor supply lines up to 50 PSIG
Part Number: MNS2-4-IN-PS-050
$1,248.00 ex GST
i h
Picture of Monnit Industrial Pressure Wireless Sensor (300 PSIG)
Monnit Industrial Pressure Wireless Sensor (300 PSIG)
Monnit’s Industrial Wireless Pressure Meter monitors gas, liquid, or vapor supply lines up to 300 PSIG
Part Number: MNS2-4-IN-PS-300
$1,298.00 ex GST
i h